Refinish the floor if the boards are sound, flat and dry. Replace sections, or plan a bigger repair, if the boards are cupped, soft or stained black, or if water is still reaching them from below. The hard part at a showing is telling those two situations apart, and a standard home inspection will only get you part of the way.
This guide is for buyers touring older homes in the Richmond area where the hardwood is original, or covered by carpet, or sanded and finished so many times nobody knows what is left. It covers what to look at in 10 minutes, the moisture facts behind most floor failures, the lead paint rule that can change your refinishing plan and what Virginia inspectors are and are not required to report.
What to check at a showing, in order
Do this walk with the lights on and, if you can, with a phone flashlight held low along the floor. Light at a low angle shows ridges and dips that a ceiling light hides.
- Look across the room at low light. Boards whose edges sit higher than their centers are cupped. Boards that are higher in the middle are crowned. Both point to moisture, and the direction tells you where to ask questions.
- Walk the whole floor slowly. A bounce, a dip or a loud squeak that repeats in the same spot can mean loose boards or a weak subfloor. Squeaks alone are usually a fastener issue. A soft spot is a bigger one.
- Check the gaps. Wide gaps between boards can be seasonal or a sign of repeated drying. Dirt packed into gaps makes the problem worse over time.
- Look near water. Check under the kitchen sink, beside the dishwasher, at exterior doors, in front of the refrigerator and around the tub. Dark patches in the grain near those spots can be water stains in the wood itself.
- Lift a floor register or look in a closet. Where the floor ends at a vent or a threshold, you can often see the thickness of the wood and the subfloor under it.
- Look at the rooms below. A basement or crawl space ceiling under a floor with trouble can show staining, mold or a damp smell.
- Look at rugs and furniture placement. A rug over one patch of floor in an otherwise open room is worth a question.
If the home has a crawl space, read our guide to a wet crawl space in older Richmond homes, since that is where many floor moisture problems begin.
Refinish or replace: how the decision usually breaks down
Refinishing sands off the top layer of the wood and applies a new finish. It works when the damage is in the finish, such as scratches, dull spots and worn areas. It does not fix a floor that is structurally wrong: loose, soft, badly cupped or deeply stained by water. Replacement, or a patch of new boards woven into the old ones, is what you plan for when the wood or the subfloor beneath it is the problem.
Questions to settle before you price either path:
- How much wood is left above the tongue and groove? A flooring contractor can check this at an edge, and a floor that has been sanded several times may have little to give.
- Is the floor solid hardwood or engineered? Engineered boards have a thin top layer, so they may take fewer sandings. A contractor can tell at a floor register or board edge.
- Is the floor flat? A cupped board that has dried may flatten after the moisture source is fixed, or it may stay warped.
- Are there different species or widths in different rooms? That makes color matching harder after a repair.
The U.S. Forest Products Laboratory’s report on moisture-related properties of wood (read in November 2026) puts the stakes plainly: flooring installed over a wet concrete slab will warp, and much of the warp may be permanent. The report also notes that moisture cycling can widen gaps between tongue and groove boards. That is why a floor that looks fine today but sits over a damp space deserves a second look. If you need a price for your plan, a local flooring contractor’s written estimate is the number to use. We did not find a sourced Richmond cost figure, so this post does not guess one.
Find older homes with original hardwood to tour
A saved search for the City of Richmond and nearby counties sends new listings as they post, so you can look for photos of the floors, compare them at a showing and bring this checklist along.
Moisture numbers that explain most floor trouble
Wood takes on and gives off water depending on the humidity of the air around it. The Forest Products Laboratory report gives the equilibrium moisture content of wood at about 70 degrees Fahrenheit, which is the moisture level wood settles at when the air stays at a steady humidity:
| Relative humidity at about 70 F | Wood moisture content it settles at | What it means for a floor |
|---|---|---|
| 50% | About 9.2% | Close to the 8% average the report recommends for interior wood at installation in most U.S. areas |
| 65% | About 12.0% | Wood has swelled, and boards may be tight or beginning to cup |
| 90% | About 20.5% | At the 20% level the report treats as the limit for preventing decay fungi |
The same report says crawl space framing has reached nearly 20% moisture content seasonally. Hardwood over a vented or damp crawl space is working against those numbers every summer. Outside the house, water running toward the foundation is the other common source, so read our guide to gutters, downspouts and lot grading as well.
A moisture meter reading on the floor and the subfloor is a number you can ask for. A flooring contractor or an inspector who offers moisture testing as an add-on service can take one. Ask for readings in several rooms, not one.
Lead paint and refinishing in pre-1978 homes
If you plan to sand a floor in an older home, ask when the house was built. The U.S. Environmental Protection Agency’s page on reducing the risk of lead exposure at home (read in November 2026) says a home built before 1978 is more likely to contain lead-based paint. It says paid workers who disturb paint in pre-1978 housing must be certified and trained in lead-safe work practices, and it says you must also be certified or hire a certified contractor if you rent part of the home, run a childcare in it or flip houses.
Floors are not the paint, but sanding creates dust, and baseboards, door trim and window casings are painted. EPA’s page says it does not address sanding floors directly, so ask a certified contractor how they would handle the trim and the dust. Add that to your quote request. For small repairs, the same page says to wet the area before sanding and clean up thoroughly. It also says not to try to remove lead-based paint on your own.
What a Virginia home inspection does and does not cover
Virginia’s 18VAC15-40-130 (read in November 2026) lists floors, the foundation, the slab floor and crawl space ventilation and vapor barriers among the items an inspector inspects. It limits the job to readily accessible components and readily observable defects, and requires the report to identify anything that could not be inspected and explain why. The section does not list moisture as its own inspection item.
That has practical effects for a hardwood floor:
- A floor covered by wall-to-wall carpet, a large rug or furniture may be listed as not fully visible.
- The inspector looks at the surface and the structure they can see. They are not asked to sand, lift or test the wood species, the finish or the thickness above the tongue.
- Moisture meter readings may be part of an inspector’s service, but the section does not require them. Ask before you hire.
- The report is not a price. If it flags a floor, get a flooring contractor’s written estimate during your contingency window.
Our Richmond home inspection guide explains how to use the inspection period to request repairs or a credit.
Where to start your search
Original hardwood is something to look for house by house, not neighborhood by neighborhood, across the City of Richmond and beyond. The question is the same whether you tour in the Fan, Church Hill, the Near West End or out in Tuckahoe. Set a floor budget before you offer. Our mortgage calculator helps you see how a repair fund changes your monthly picture, and the buy with us page walks through the steps from offer to closing.
Bring this floor checklist to your next showing
A saved search for the City of Richmond and nearby counties puts new listings in front of you early. Use the checklist above on the ones with original hardwood.
Frequently asked questions
How can I tell solid hardwood from engineered flooring?
Look at a board edge, a floor register opening or a threshold. Solid boards are one piece of wood all the way through. Engineered boards show layers, like plywood, under a thin top layer of hardwood. A flooring contractor can confirm in a minute, and the answer matters because a thinner top layer may allow fewer sandings.
Will sanding remove dark stains from pets or water?
Not always. Stains that go into the grain can be deeper than a sanding pass. Black stains from long term water exposure often mean the wood fibers have changed, and a contractor may recommend replacing those boards. Ask for a sample patch in an out of the way spot before you decide.
Is a squeaky floor a deal breaker?
No, but find the cause. A squeak in one spot is often loose boards or fasteners, and a contractor can often address that without replacing the floor. A squeak that comes with a dip, a soft spot or damp smell points to the subfloor or a moisture issue, and that is worth a closer look and a written estimate.
What humidity should I keep a hardwood floor at after I buy?
The Forest Products Laboratory report puts wood moisture content near 9.2% at 50% relative humidity and near 12.0% at 65%, measured at about 70 degrees Fahrenheit. Keeping indoor air steady rather than swinging between damp summers and dry winters is the practical lesson. A small humidity gauge costs little and shows you the trend.
Is cupping always a moisture problem?
The Forest Products Laboratory describes cupping as different dimensional change across a board’s width, which happens when one face of a board takes on or loses moisture faster than the other. So yes, it traces back to moisture, but the source can be a damp space below, a leak or a very humid season. Finding the source matters more than the label.
Can I ask the seller to refinish the floors as part of the contract?
You can ask for a repair, a credit or a price change through your agent during negotiation. Whether the seller agrees is up to them. Contract terms are legal matters, so this is general information, not legal advice. Ask a Virginia real estate attorney if you need the language reviewed, and get a contractor’s written estimate first.
